Carriage (Y-axis) belt - Drives the carriage assembly for 54 inch size plotters. (36 inch size order C4704-60207)
Y-axis motor bracket - Includes edge wire saddle - Holds the Y-Axis motor
Pincharm spring retaining bushing
Cutter bushing - Connects cutter assembly to slider rod
Hard drive power cable - Has 4-pin (F) connectors - 47.6cm (18.8in) long
Ribbon cable for one IDE drive - Has 40-pin (F) connectors - 31.8cm (12.5in) long
Pinch arm cam - Attached to pinch arm (Media) lever
Left cam journal - Mounted on left end of pinch arm shaft
Spindle end cap - Small core spacer - Removes for loading the media roll. Please order spindle assembly.
Carriage assembly - Includes carriage assembly, line sensor, encoder, rear bushing, calibration pen, digitizing sight, guages - Trailing cable and cable clamp not included
Encoder strip roof
One Line sensor lens cover for carriage - Mounts to carriage assembly for HP Designjet Plotters.
Right end cover - Has cut outs for the control panel
Left end cover for HP DesignJet 2000CP
Rollfeed access cover - Opens forward to allow access to paper spindle assembly
4.3GB hard disk drive. This Hard Disk Drive is the direct replacement part for the internal hard disk drive for the HP DesignJet 2500cp, 3500CP, 3800CP, and other models.
Elevator platform assembly - Raises and lowers ink cartridges to fill the print heads - Located on left side of plotter
Firmware SIMM kit (Revision A.04.08) - Mounts in the electronics module - NOTE: this is not a postscript SIMM
Overdrive gear cluster
Encoder ground strap - Provides ground to end of encoder strip
Starguard starwheel cover assembly
Housing assembly (on left side)
SYNTHETIC OIL (4oz Plastic Bottle) Front and Rear Slider Rods Synthetic oil - One plastic bottle of 3.5oz / 118.29 ML
External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and three parallel (DB-25) output connectors
Bail motor for HP DesignJet 3000CP
Carriage (Y-Axis) motor assembly - Drives carriage belt - Includes motor, motor holder, and cable
Paper for DesignJet 1055 Series, DesignJet 800 Series, DesignJet 130 Series, DesignJet 500. Bond Paper - 24 inch x 150.
Refill interconnect board
JetDirect 400N modular input/output (MIO) internal print server - Provides 10/100Base-TX or 10Base-2 network connection using RJ45 or BNC connectors
JetDirect 400N modular input/output (MIO) - Internal print server - Provides 10/100Base-T or 10Base-2 network connection using RJ45 or BNC connectors
External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and three parallel (DB-25) output connectors
HP JetDirect 500X external token ring print server module - Interfaces up to 3 parallel printers to an ethernet 10Base-T (RJ-45), 10Base2 (BNC), or 100Base-TX (RJ-45) LAN
Pincharm assembly - Curved black plastic plate with four small rubber rollers - Does NOT include spring or bushing
Refill assembly - Mounted inside the left hand cover - Includes motor and gears
Paper drive (platen) roller assembly - Long gear driven roller
Right end cover and window closed sensors - Includes cable and connector
Pincharm sensor
Left end cover sensor - Includes cable and connector
Take-up reel sensor assembly
Service station assembly for Hewlett Packard Designjet Plotters.
Compression spring - Installed between pincharm assembly and bushing
Service station spring
Starwheel mount assembly - Includes cover, body, spring and two starwheels
Encoder strip - Used to determine carriage position 54inch.
Roller support bracket
Take-up reel left hand support assembly
Stand-by switch asembly
Right trim assembly - At right of entry platen
Left trim assembly - At left of entry platen